Quick starts

Tune camera feel and transitions

Set how fast the camera flies between views, how it banks and pulls back, how orbit and zoom respond, and when it turns by itself, for the whole product at once.

Camera feel is shared across all views of a product, not authored per camera. It lives on one BAKR Global Settings Data Asset. A camera overrides a value only when you tick that override on its Settings.

Quick start

  1. In the Content Browser, choose Add → Miscellaneous → Data Asset → BAKR Global Settings. Name it DA_Lamp_Camera.
  2. On the configurator, open 04 - Cameras and assign it to Global camera & UI settings.
  3. Open the asset, change a value, press Play and switch cameras. Repeat until it feels right.

Leaving the slot empty uses the built-in defaults, so you only need an asset when you want to change something.

Configurator camera step with the Global camera and UI settings asset slot
Assign shared camera settings to give every view on the product a consistent feel.

The settings that matter most

SettingDefaultWhat it changes
Transition Seconds1.6Flight time between views. 1 to 2 feels calm; below 0.6 feels like a jump.
Transition Pull Back0.5How far the camera dollies out mid-flight, as a fraction of its distance to the pivot. 0 flies at a constant distance.
Roll during transitionsOn, 22°A drone-like bank during flights. Below 5° reads as natural.
Orbit Sensitivity3How far one drag turns the camera.
Orbit Smoothing12How fast orbit catches up with the input. Lower glides further.
Zoom Step35 cmDistance per scroll notch or pinch step.
Min / Max Arm Length100 / 1200 cmZoom limits for every view without its own.
Exterior Panel Offset-1.5 mmHow far the picture shifts sideways while the panel is open, in mm of camera sensor.

Every setting, with its default, is in the Global settings reference.

Make flights smarter

  • Scale pull back with orientation change gives a front-to-rear switch the full dolly and a small nudge almost none.
  • Scale Transition With Distance makes short hops quicker and long flights slower, between Min and Max Transition Scale.
  • Scale roll with distance keeps short hops level and banks fully on long sweeps.
  • Roll Duration longer than Transition Seconds lets the bank ease out after the camera lands, which reads as weight.
Global camera transition duration, pull back and distance scaling settings
Shape the speed and path of flights between views, including how pull back responds to a change of direction.

Art-direct with curves

Assign Float Curves (time and value 0 to 1) to Transition Ease Curve, Transition Rotation Curve, Transition Pull Back Curve and Transition Roll Curve. Curves are stretched to their own end points, so the camera always lands exactly on the view. An ease or rotation curve can overshoot on the way. That is your call, and the editor warns when a curve does not start and end at rest.

Transition ease, rotation and pull back curve asset slots
Use curves to give camera movement a distinctive pace and shape.

Interior fade

Views marked Interior cut behind a fade instead of flying. Fade interior transitions (on by default), Interior Fade Out / Hold / In Seconds, Interior Fade Color and Interior Fade Curve set how it looks. The same fade is used by a product switch set to Fade.

Interior fade enabled with fade out, hold, fade in, color and curve settings
Control the timing and appearance of transitions into interior views.

Turntable when idle

Tick Auto orbit when idle. After Auto Orbit Idle Seconds without input, the camera sweeps left and right inside the view's yaw limits at Auto Orbit Speed degrees per second. A view with a full-circle yaw range turns continuously. Any orbit, zoom, panel change or camera switch restarts the countdown.

Global orbit sensitivity and smoothing settings and zoom step and arm length limits
Tune how orbit and zoom respond across the product's camera views.
Auto orbit and comfort settings, including reduced motion and camera inertia
Set idle movement and motion comfort preferences for the whole product.

Comfort

  • Reduced motion drops the pull back and roll, shortens flights by Reduced Motion Transition Scale and turns auto orbit off. No camera can override it. Visitors can switch it at runtime with the reducedMotion web command or the Set Reduced Motion Blueprint node.
  • Disable camera inertia makes orbit and zoom follow input exactly, without gliding.

Override per camera

On a camera's Settings, tick an override to author it for flights to that view only: Transition Seconds, Transition Pull Back, Override transition curves, Override transition roll, Override zoom limits and Override auto orbit. Unticked follows the asset.